Installation Instructions
Part Number 510-761 Jr. Kit
2000-04 Toyota Tundra 4.7L
2001-04 Toyota Sequoia 4.7L
Packing List:
#1 850-144 Airaid Premium Filter 1
#2 KIT918T Modular Intake Tube 1
#3 KITHUMPS11 Urethane Hump Hose 1
#4 KITRDCR04 Reducer Coupler 1
#5 KITHOSE01 1/2” x 13” Breather Hose 1
#6 KITHOSE06 3/8” x 17” Hose 1
KIT761HP Hardware & Instructions 1
#7
KITHS56 #56 Hose Clamp 1
#8 KITHS60 #60 Hose Clamp 1
#9 KITHS52 #52 Hose Clamp 2
#10 KITFITTING10 1/4” Barb x 1/8” NPT Fitting 1
#11 KITHOSE03 1/4” x 4” Hose 1
#12 KIT15DHC3050 1/4 - 20 x 1/2” Button Head Bolt 1
#13 KIT09FWZ019 1/4” Flat Washer 1
#14 KITFITTING11 1/4” x 1/4” x 1/8” Vacuum Tee 1
#15 KITFITTING13 1/4” x 1/4” x 3/8” Tee 1
#16 KITSNP14M4 #14 Speed Clamp 1
Tools Required For Installation:
5/32” Allen Wrench
5/16” & 10mm Socket
Ratchet & Extension
7/16” Wrench
1. Disconnect negative battery cable.
A) Remove two 10mm nuts, and remove beauty
cover. (Save for reuse). B) Remove the bolt thru
the Adel clamp that holds the air conditioning
hose.
3. Loosen the hose clamps on the intake tube at
the throttle body, and at the airbox.
4. Remove the factory intake tube from the ve-
hicle.
7. Install the small end of the urethane hump
hose (#3) and the #56 hose clamp (#7) over the
factory airbox. Install the #60 hose clamp (#8)
onto the other side of the urethane hump hose.
Next install the reducer coupler (#4), small side
first, onto the throttle body with two #52 hose
clamps (#9). Leave the clamps loose for now.
6. Remove the factory air filter, and install the
Airaid Premium Filter (#1). Reinstall the fac-
tory airbox lid, and latch 4 clips.
9. Install the MIT into the urethane hump hose
first, and then into the reducing coupler. Adjust
the MIT snugly against the throttle body, and
tighten the 4 hose clamps. Next install the 1/4 -
20 button head bolt (#12) and 1/4” flat washer
(#13) thru the Adel clamp and into the MIT to
hold the air conditioning hose.
8. Install the 1/4” Barb x 1/8” NPT Fitting (#10)
into the Airaid Modular Intake Tube (MIT)
(#2) as shown. Now slide the 1/4” x 4” hose
(#11) onto the barb fitting.
A.
B.
5. Unlatch the 4 clips on the factory airbox, and
remove the lid.
2. A) Disconnect the breather hose at the valve
cover. B) Disconnect 1/4” and 1/8” vacuum
lines on the back of the factory intake tube. C)
Unclip MAF wire harness retainer from the
intake tube. D) Sequoias and 2000-02 Tundras
only; remove 3/8” vacuum hose between fac-
tory intake tube and metal fitting on top of the
intake manifold. (Hose Not Shown)
A..
B.
C.
D.
Kommentare zu diesen Handbüchern