Airaid 400-226 Bedienungsanleitung PDF herunterladen

Installation Instructions

For Part Numbers:

400-226 720-473 Airaid Oiled Media Filter

401-226 721-473 SynthaMax Dry Media Filter - Red

402-226 722-473 SynthaMax Dry Media Filter - Black

403-226 723-473 SynthaMax Dry Media Filter - Blue

2009-10 Ford F-150 4.6L, 5.4L V8

2008-10 Ford F-250/F-350 Super Duty

5.4L V8, 6.8L V10

1. Disconnect the negative battery cable!

A.) Using the pr ovided #20 Tor x Bit remove two

screws and the Mass Air Flow (MAF) sensor from the

factory intake tube. There is no need to disconnect the

wiring harness.

B.) Loosen the factor y hose clamp.

C.) Unlatch 3 clips that secur e the air box lid to the

base.

2. Remove the factory airbox lid from the vehicle by

sliding the flexible tube off of the airbox lid neck, and

then rotate the lid up and out of the base.

3. Remove the factory air filter from the airbox base.

4. Assemble the two Quick Fit panels (#3 & #4) as

shown using four 6-32 screws (#6) flat washers (#7)

and kep nuts (#8).

5. Install the MAF Adapter Tube (#2) into the Quick Fit

Panel as shown using four 1/4-20 button head bolts (#9)

and flat washers (#10). Make sure the slot for the MAF

sensor is on the left side when looking from this view.

6. Install the Quick Fit Assembly onto the top of the

factory airbox base sliding the four tabs on the panel

into the slots on the base and then latching the three

factory latches. Slide the factory intake tube over the

MAF tube and tighten the factor y hose clamp as

shown.

7. Reinstall the MAF sensor into the Airaid Adapter

Tube using two 8-32 x 3/8” button head screws (#11).

Do Not Use The Factory Screws !

8. Install the Airaid Premium Filter (#1) onto the adapt-

er tube and tighten the hose clamp. Next install the

weather strip (#5) onto the top of the Quick Fit panels

as shown.

Component Identification

1. Airaid Premium Filter 1

2. MAF Adapter Tube 1

3. Front Panel 1

4. Rear Panel 1

5. Weather Strip 16 1/2” 1

6. 6-32x5/16” Screw 4

7. #6 Flat Washer 4

8. 6-32 Keps Nut 4

9. 1/4-20 Button Head Bolt 4

10. 1/4” Flat Washer 4

11. 8-32x3/8” Button Head Screw 2

12. #20 Torx Security Bit 1

9. Double check your work!

Make sure there is no foreign material in the

intake path. Make sure all clamps, hoses,

bolts, and screws are tight.

intake path. Make sure all clamps, hoses,

bolts, and screws are tight. Periodically check

the tightness of all hose clamps.

10. Re-connect the negative battery

cable!

Full color instructions can be viewed on our web site at Airaid.com. Use the Product Search function to find your part number, and click View Details.

1 2

Inhaltsverzeichnis

Seite 1 - Installation Instructions

Installation Instructions For Part Numbers: 400-226 720-473 Airaid Oiled Media Filter 401-226 721-473 SynthaMax Dry Media Filter - Red 402-226 722

Seite 2 - For your Oiled media filter

Airaid Filter Co. 2688 E Rose Garden Ln. Phoenix AZ 85050 (800) 498-6951 [email protected] www.airaid.com REV.10.24.13 P/N 790-551 Aerosol Spr

Verwandte Modelle: 401-226 | 402-226 | 403-226 |

Kommentare zu diesen Handbüchern

Keine Kommentare

Airaid 400-226 Bedienungsanleitung

Stöbern Sie online oder laden Sie Bedienungsanleitung nach Luftausrüstung Airaid 400-226 herunter. Airaid 400-226 User Manual Benutzerhandbuch

Inhaltsverzeichnis

Verwandte Modelle: 401-226 | 402-226 | 403-226 |

Kommentare zu diesen Handbüchern

Verwandte Produkte und Handbücher für Luftausrüstung Airaid 400-226