Airaid 400-231 Bedienungsanleitung

Stöbern Sie online oder laden Sie Bedienungsanleitung nach Luftausrüstung Airaid 400-231 herunter. Airaid 400-231 User Manual Benutzerhandbuch

  • Herunterladen
  • Zu meinen Handbüchern hinzufügen
  • Drucken
  • Seite
    / 2
  • Inhaltsverzeichnis
  • LESEZEICHEN
  • Bewertet. / 5. Basierend auf Kundenbewertungen
Seitenansicht 0
Installation Instructions
For Part Numbers:
400-231 720-478 Airaid Oiled Media Filter
401-231 721-478 SynthaMax Dry Media Filter - Red
402-231 722-478 SynthaMax Dry Media Filter - Black
403-231 723-478 SynthaMax Dry Media Filter - Blue
2009-2010 Ford F-150 5.4L
2007-14 Ford Expedition 5.4L
1. Disconnect the negative battery cable!
Loosen the two intake clamps and remove the Factory
intake tube.
3. Remove the factory air filter from the lower half of
the airbox.
4. Assemble the two Quick Fit panels (#3 & #4) as
shown using four 6-32 screws (#9) flat washers (#11)
and kep nuts (#10).
5. For F-150 models only:
Fasten the Extension panel (#5) to the outside of the
panel assembly using the remaining 6-32 screws, flat
washers, and kep nuts.
6. A.) Install the Silicone Hump Hose (#7) and two #64
Hose Clamps(#14) onto the Quick Fit assembly. Leave
the clamps loose for now.
B.) Install the assembly onto the lower half of the fac-
tory airbox. Slide the metal tabs into the airbox slots,
and fasten the 3 airbox clips.
7. Install the Silicone Coupler (#6), one #64 Hose
Clamp(#14), and the #52 Hose clamp (#13) onto the
engine air inlet. Leave the clamps loose for now.
8. Transfer the MAF sensor into the Airaid Intake
Tube (#2) and secure using two 8-32 x 1/2” button
head screws (#11). Do Not Use The Factory Torx
Head Screws !
Component Identification
1. Airaid Premium Filter 1
2. Airaid Intake Tube 1
3. Front Panel 1
4. Rear Panel 1
5. Extension Panel 1
6. Silicone Reducer Coupler 1
7. Silicone Hump Hose 1
8. Weather Strip 23” 1
9. 6-32 x 5/16” Screw 9
10. 6-32 Keps Nut 9
11. #6 Flat Washer 9
12. 8-32 x 3/8” Button Head Screw 2
13. #52 Hose Clamp 1
14. #64 Hose Clamp 3
15. T-20 Torx Driver 1
2. A.) Disconnect the Mass Air Flow (MAF) Sensor.
B.) Unfasten the three airbox clips on the left side, and
remove the upper half of the factory airbox.
A
Tabs
#52
#64
9. A.) Insert the Airaid Intake Tube into the couplers as
shown. Check for alignment, and tighten all clamps.
B.) Re connect the Mass Air Flow Sensor.
Note: Tab is outside
Full color instructions can be viewed on our web site at Airaid.com. Use the Product Search function to find your part number, and click View Details.
Seitenansicht 0
1 2

Inhaltsverzeichnis

Seite 1 - 2009-2010 Ford F-150 5.4L

Installation Instructions For Part Numbers: 400-231 720-478 Airaid Oiled Media Filter 401-231 721-478 SynthaMax Dry Media Filter - Red 402-231 722

Seite 2 - Tune-Up Kit!

Airaid Filter Co. 2688 E Rose Garden Ln. Phoenix AZ 85050 (800) 498-6951 [email protected] www.airaid.com REV.04.09.04 P/N 790-551 Aerosol Sp

Verwandte Modelle: 401-231 | 402-231 | 403-231 | 400-256 | 401-256 | 402-256 | 403-256 |

Kommentare zu diesen Handbüchern

Keine Kommentare