Airaid 450-304 Bedienungsanleitung PDF herunterladen

Installation Instructions

For Part Numbers:

450-304 700-466 Airaid Oiled Media Filter

451-304 701-466 SynthaMax Dry Media Filter - Red

452-304 702-466 SynthaMax Dry Media Filter - Black

453-304 703-466 SynthaMax Dry Media Filter - Blue

2005-09 Ford Mustang GT

4.6L V8 RACE ONLY

Please Note: This intake system is not calibrated to

any ECU and requires a custom tune for proper

Mass Air Sensor functionality and maximum per-

formance. It is designed for “RACE ONLY”

1. Disconnect negative battery cable.

PLEASE READ #22 ON THE BACK PAGE!!

Push the green plastic tabs, and remove breather

hose from vehicle. (Save for later use).

2. Loosen the intake tube hose clamp on the throttle

body. Slide the red tab on the electrical connector, and

disconnect the mass air sensor.

3. With a 10mm socket, remove the bolt holding

the factory airbox to the fender and save the bolt.

It will be reused

4. Remove the complete factory intake. Use cau-

tion to retain the factory grommets in the inner

fender.

5. Using the provided #20 torx bit, remove two screws

and the mass air sensor from the factory airbox lid. Note

the direction of the sensor for proper re-installation later.

(Save the mass air sensor for re-installation in step #13,

the factory screws will not be re-used).

6. With a 10mm socket, remove and save the bolt

from the anti-lock brake bracket. It will be re-

installed later in step #9.

7. Install the air filter adapter (#5) into the Cool

Air Dam (#7) as shown, using 3 button head

bolts (#9) and ¼” flat washers (#10).

Component Identification

1. Airaid Premium Filter 1

2. Airaid Intake Tube 1

3. Urethane Oval Coupler 1

4. Urethane Hump Hose 1

5. Filter Adapter 1

6. Cool Air Dam 1

7. 3/8”x12” Hose 1

8. Weather Strip 22” 1

9. ¼-20 Button Head Bolt 3

10. ¼” Flat Washer 3

11. 8-32 x 3/8” Button Head Bolt 2

12. #72 Hose Clamp 4

13. Grommet 1

14. Aluminum Spacer 1

15. 1/4” Fender Wasker 1

16. Aluminum Fitting 1

17. #20 Torx Bit 1

10. Install the hump hose (#4) on the filter adapt-

er (#6), with two #72 hose clamps (#12). Tighten

only the clamp next to the CAD.

11. Install the supplied grommet (#13) and aluminum

fitting (#16) into the Airaid intake tube as shown.

9. Slide the Aluminum Spacer (#14)underneath the

CAD and into the hole as shown. Secur e the

CAD to the inner fender using the OEM bolt from

step #3 and the supplied 1/4” Fender Washer (#15).

8. Place the CAD into the inner fender, align the bolt

holes and re-install the bolt from step #6.

12. Align the two slots in the tubes, and install the

factory mass air sensor removed from step #5.

Make sure the screw holes line up, then install the

two supplied button head screws. (#11).

DO NOT USE THE FACTORY SCREWS!!

Full color instructions can be viewed on our web site at Airaid.com. Use the Product Search function to find your part number, and click View Details.

1 2

Inhaltsverzeichnis

Seite 1 - Installation Instructions

Installation Instructions For Part Numbers: 450-304 700-466 Airaid Oiled Media Filter 451-304 701-466 SynthaMax Dry Media Filter - Red 452-30

Seite 2 - Tune-Up Kit!

19. Double check your work! Make sure there is no foreign material in the intake path. Make sure all clamps, hoses, bolts, and screws are tight. Doubl

Verwandte Modelle: 451-304 | 452-304 | 453-304 |

Kommentare zu diesen Handbüchern

Keine Kommentare

Airaid 450-304 Bedienungsanleitung

Stöbern Sie online oder laden Sie Bedienungsanleitung nach Luftausrüstung Airaid 450-304 herunter. Airaid 450-304 User Manual Benutzerhandbuch

Inhaltsverzeichnis

Verwandte Modelle: 451-304 | 452-304 | 453-304 |

Kommentare zu diesen Handbüchern

Verwandte Produkte und Handbücher für Luftausrüstung Airaid 450-304