Airaid 200-126-1 Bedienungsanleitung PDF herunterladen

Installation Instructions

For Part Numbers:

200-126-1 700-450 Airaid Oiled Media Filter

201-126-1 701-450 SynthaMax Dry Media Filter - Red

202-126-1 702-450 SynthaMax Dry Media Filter - Black

203-126-1 703-450 SynthaMax Dry Media Filter - Blue

2004-05 Buick Rainer

2002-05 Chevrolet Trailblazer

2002-05 GMC Envoy

2003-05 Isuzu Ascender

2002-04 Oldsmobile Bravada

4.2L I6

Component Identification

1. Airaid Premium Filter 1

2. Air Dam Assembly 1

3. Plastic Intake Tube 1

4. Weather Strip 21½” 1

5. Urethane Hump Hose 1

6. Grommet Plug (In Tube) 1

7. M6-1x25 Hex Bolt 3

8. ¼-20 x 5/8” Hex Bolt 2

9. 3/16” Flat Washer 3

10. 3/16” Lock Washer 2

11. #60 Hose Clamp 2

12. Grommet 1

13. Hose Fitting Adapter 1

14. Rubber Grommet 1

Full color instructions can be viewed on our web site at Airaid.com. Use the Product Search function to find your part number, and click View Details.

I DISCONNECT NEGATIVE (-) BATTERY CABLE

II Remove Factory Intake Assembly

A) Using a Phillips head screwdriver, loosen the three screws holding the factor y air box lid in place and r emove. See Fig#1 (Note: Bottom air box

section will remain in place.)

B) Using a flat blade screwdriver, carefully remove the air temper ature sensor from the factor y intake tube. See Fig#2 (Note: Retain parts for later

use)

C) 2004 Short Wheel Base Only. Grasp and fir mly squeeze the air injection connector as shown and remove. Fig#3

D) Loosen the hose clamp on the engine side of the factory intake tube using a flat head screwdriver.

E) Remove the factory intake tube and stock air filter while leaving the lower air box section in place. See Fig#4 (Hint: lower air box section is also

the windshield washer fluid reservoir)

III Assemble the Airaid Intake System

A) Insert the supplied r ubber gr ommet along with the r etained factory air temper ature sensor into the small hole located on the r ear of the curve

on the Airaid tube. See Fig#5

B) 2004 Short Wheel Base Only. Insert the lar ge r ubber grommet and hose connector adapter into the hole located on the under side section of the

Airaid intake tube. See Fig#6 & 7 Use the plug grommet for all other vehicles without air injection.

C) Assemble the Air aid intake tube and air dam with the supplied ¼” bolts and washers Refer to Fig#8

D) Slide the Air aid urethane hump hose and supplied hose clamps over the curved end of the Air aid intake tube. Refer to Fig#7

IV Install the Airaid Intake System

A) Place the complete Airaid intake assembly into the engine compartment and align. Refer to Fig#9

B) Position the Airaid cool air dam assembly on top of the windshield washer fluid reser voir using the har dwar e pr ovided. See Fig#9 (Note: leave

hardware loose for later adjustment)

C) Mount the Airaid Premium air filter onto the end of the tube and tighten the hose clamp. Refer to Fig#9

D) Slide the Air aid urethane hump hose and hose clamps over the factor y air box located on the top of the engine. Make sur e ther e is an adequate

amount of urethane hose covering both the Airaid intake tube and air box. See Fig#9

E) 2004 Short Wheel Base Only. Reconnect the air injection connector Fig#10 and the air temper atur e sensor connector . Fig#11

F) Check alignment of complete air dam assembly and tighten remaining hose clamps and fasteners.

G) Install weather strip on air dam. Refer to Fig#9 (Hint: Start from one corner of the air dam and press the weather strip firmly onto the panel while

working your way out to each end of the air dam. This will insure that the weather strip is installed correctly and allow for ease of installation)

VI Finishing Up

A) Make sure that the intake path is clear of all debr is!

B) Check alignment of the Air aid intake tube and tighten all clamps, brackets, nuts & bolts.

C) Inspect your overall work and check for clear ance between air dam assembly and the hood.

D) Re-connect the negative battery cable.

Fig#1 Fig#2 Fig#3 Fig#4

1 2

Inhaltsverzeichnis

Seite 1 - Fig#1 Fig#2 Fig#3 Fig#4

Installation Instructions For Part Numbers: 200-126-1 700-450 Airaid Oiled Media Filter 201-126-1 701-450 SynthaMax Dry Media Filter - Red 202

Seite 2 - Fig#5 Fig#6 Fig#7 Fig#8

Airaid Filter Co. 2688 E Rose Garden Ln. Phoenix AZ 85050 (800) 498-6951 [email protected] www.airaid.com P/N 790-551 Aerosol Spray P/N 790-5

Verwandte Modelle: 201-126-1 | 202-126-1 | 203-126-1 |

Kommentare zu diesen Handbüchern

Keine Kommentare

Airaid 200-126-1 Bedienungsanleitung

Stöbern Sie online oder laden Sie Bedienungsanleitung nach Luftausrüstung Airaid 200-126-1 herunter. Airaid 200-126-1 User Manual Benutzerhandbuch

Inhaltsverzeichnis

Verwandte Modelle: 201-126-1 | 202-126-1 | 203-126-1 |

Kommentare zu diesen Handbüchern

Verwandte Produkte und Handbücher für Luftausrüstung Airaid 200-126-1